The EMDAR Contact Board module allows management of EMDAR contacts. A contact is an untracked EM emissions pattern thought to indicate a Tactically Significant Maneuvering Object (TSMO). As the EMDAR system is not directional and becomes less accurate over distance operators will typically spend some time managing contacts before accurate enough information can be obtained to achieve tracking with a narrowband array.
A contact represents the estimated position of a possible TSMO based on an indicative EM emissions patterns on the Waterfall Displays. By selecting the range to the patterns (on one lateral array and one longitudinal array) the range and bearing to this point in space is calculated.
It is unlikely that the TSMO's position will be estimated accurately enough on the first contact for tracking purposes. Multiple contacts will likely need to be created for each target as EM patterns are detected (where a target TSMO maneuvers, for example, thereby temporarily increasing its EM output) to refine its location. To help match contacts with their target, each suspected target is given a tag and each contact associated with that target is also assigned that tag.
On the tactical overlay, each tag has its own color:
Sierra: Silver (grey)
Bravo: Blue
Victor: Violet
Tango: Tan (gold/yellow)
This is particularly useful when multiple TSMO targets are suspected.
The contact board provides data on the range and bearing of each contact at the time it was added. Until acquired by a narrowband array a contact cannot be tracked. A contact’s estimated location is defined as a particular point in space and the contact board will update the range and bearing to that point based on movement of the vessel, but not on any shift in location of the contact itself.
A contact’s details can be updated at any time, where the contacts position has been refined, where its tag needs to be changed or if the contact is no longer relevant and can be re-used. Each contact has a time indicating the time elapsed since it was added or last updated.
Once a contact’s EM emissions are strong enough to make tracking possible, the most accurate contact is assigned to a narrowband array. These are a more focussed and directional version of the passive arrays used by the EMDAR system, that can track the movement of an EM source once acquired.
The contact board can display up to ten contacts. This limit is imposed by the computation resources required to manage the relative position of the vessel and contacts.
The EMDAR Contact Board has two operating modes.
This mode displays contacts currently being managed by the EMDAR team without any associated designation or assignment controls. The commanding officer will likely have a contact board in this mode displayed on one of their command consoles, for example.
This mode allows contacts to be added to the board, updated and assigned to narrowband arrays. In this mode, the contact board works in conjunction with other EMDAR modules including waterfall displays and the EMDAR monitor. An EM pattern is targeted on the waterfall displays, assessed on the EMDAR Monitor and then added to the contact board.
Each contact is displayed underneath it’s designation, which includes a system-assigned contact number. This number is the primary means of identifying a contact, as the tag may change at any time. The number is unique to the current mission phase and is not re-used (until the contact board is reset – see below).
Each contact displays the relative range and bearing to the source EM’s location in space at the time of the contact’s creation or update. The range in bearing is updated to reflect movement of the vessel but not the movement of the source EM pattern (as there is nothing for the system to track).
A timer indicates how long it has been since a contact was added or updated. The timer will change colour to alert and then alarm status after a predefined time to prompt the operator to update the contact.
Using the EMDAR waterfall displays, select ranges on one of the longitudinal arrays and one of the lateral arrays (this selection will usually be based on the location of EM patterns of interest).
Selecting these ranges will update the EMDAR monitor with a bearing and directional range and will display the EM profile for that location.
Updating a contact is required when its tag changes or where it is preferable to refine the contact's location rather than create a new contact (where the contact is about to be assigned to a narrowband array, for example).
Contacts can be removed from the board when it is no longer necessary to manage a contact (because the source EM pattern has disappeared from the waterfall display, for example).
The deleted contact’s designation number will not be re-used unless the board is reset, to avoid confusion.
All contacts can be removed from the board at once with the Board button group.
Where a contact’s location is considered accurate enough it becomes possible to direct a narrowband array to acquire and track the contact source.
If a contact is tracked it will remain on the contact board, but its range and bearing will be updated automatically as long as it remains tracked.
A tracked contact (or "track") is identified by a green bearing track.on the central visualisation and the display of the TRACKED button with active status.
The contact's designation number is replaced by a unique code.
The elapsed time is replaced by an estimate of the TSMO's speed.
All tracks appear as green on the tactical overlay and are labelled with the contact's number. As such, tracks do not use tag colours - they are assigned a designation instead. The designation indicates the target's tactical posture:
Sierra: Unkown posture
Bravo: Friendly posture
Tango: Threat posture
Victor: Neutral posture
When created a track retains the equivalent designation the contact was tagged with, but this should be changed to the appropriate designation.
To release the designation from a track, use the same procedure as if you were deleting a contact (see above). The first time you do this with a contact, it will remove the designation. If you use the deletion procedure again on a track that does not have a designation, the track will be deleted.
It is possible to add a designation back to a track (or change an existing designation) using the same procedure as for contacts.
A track may be released manually by tapping the contact's TRACKED button. A confirmation dialog will ask for confirmation of the release.
A track is lost if the TSMO goes out of EMDAR range or where an AO comes between the vessel and the TSMO.
If a release or loss occurs, the track will revert to a contact. The contact's position will be updated with the last tracked position of the TSMO.